The universal i2C Display AD interface with a black and white display supports about 40 functions that you can use in programming different interfaces (Arduino, Raspberry, micro: bit, ...). The interface is Display AD is Arduino UNO compatible and uses ATMEGA328 microprocessor at 16 Mhz. To allow you to program the interface, we have installed a programming connector. The interface can be programmed as an Arduino UNO or via a programmer. The interface uses a screen with a resolution of 84x48 pixels for graphic or textual display.
For the audio output, a 0.5W speaker with a volume control is installed and connected to pin 2 of the microcontroller. To receive data from different sensors, three input connectors are used which are connected to pins A1, A2, A3, and two I2C connectors (5V and 3.3V). Sensors with a signal up to 9V can be connected to the inputs. To power the sensor, the interface has two outputs with a power supply of 3.3V and 5V. A 9V battery (or a 5V connector on the UNO / MEGA interface) or a 5V USB adapter can be used to power the interface.
ROB00191
Uno-T5 board ( Arduino UNO - fischertehnik ) power conn. 5.2 x 2.1 mm
23
.44
Discount for bigger quantity.
Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 8x OUTPUT - max 600 mA for each output (depending on input voltage), 4 x DC motor or 8
x LED, 8 x INPUTS ( outputs ) - 2 x digital, 6 x analog, TX + RX, I2C, , 2 x SERVO ( 5V ). Board for Arduino UNO. All inputs are with PULL UP resistors ( HIGH state ). Max. VOLTAGE on INPUTS MAX.9V.
ROB00192
Uno-T5 board ( Arduino UNO - fischertehnik ) power conn. 3.5 x 1.3 mm
23
.44
Discount for bigger quantity.
Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 8x OUTPUT - max 600 mA for each output (depending on input voltage), 4 x DC motor or 8
x LED, 8 x INPUTS ( outputs ) - 2 x digital, 6 x analog, TX + RX, I2C, , 2 x SERVO ( 5V ). Board for Arduino UNO. All inputs are with PULL UP resistors ( HIGH state ). Max. VOLTAGE on INPUTS MAX.9V.
ROB00195
Mega-T5 board ( Arduino MEGA - fischertehnik ) power conn. 5.2 x 2.1 mm
30
.00
Discount for bigger quantity.
Board for Arduino MEGA (256). Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 12x OUTPUT - max 600 mA for each output (depending on input voltage),
6 x DC motor ( 5 x PWM ) or 12 x LED, 12 x INPUTS ( outputs ) - 12 x analog/digital, TX + RX, I2C, 2 x SERVO ( 5V ). All inputs are with PULL UP resistors ( HIGH state ). VOLTAGE on INPUTS MAX. 9V.
ROB00196
Mega-T5 board ( Arduino MEGA - fischertehnik ) power conn. 3.5 x 1.3 mm
30
.00
Discount for bigger quantity.
Board for Arduino MEGA (256). Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 12x OUTPUT - max 600 mA for each output (depending on input voltage),
6 x DC motor ( 5 x PWM ) or 12 x LED, 12 x INPUTS ( outputs ) - 12 x analog/digital, TX + RX, I2C, 2 x SERVO ( 5V ). All inputs are with PULL UP resistors ( HIGH state ). VOLTAGE on INPUTS MAX. 9V.
ROB00202
Pi-T5 - interface for Raspberry Pi (connector 5.2 x 2.1)
35
.62
Discount for bigger quantity.
Interface specification: 8 x OUTPUTS (max 600mA), 8 x Digital INPUTS, 4 x Anlogue INPUTS, 2 x SERVO connector (5V), supply connectors (OUT) - 1 x 5V i 1 x 3,3V, 1 x UART connector (TX,RX), 1 x i2C connector, power supply connector for Raspberry and Interface ( 5.2 x 2.1 mm ), 1 x connector for 9V battery ( min. 1800 mA
). Interface dimension 73 x 62 mm. The interface is compatible with all Raspberry models that have a compatible connector with version 3. The adapter requires a min. 2500 mA 9V. VOLTAGE on INPUTS MAX. 9V. Separate connector (5V) to power the SERVO motor. SERVO motors can also be used with the Raspberry Pi 4 interface.
ROB00203
Pi-T5 - interface for Raspberry Pi (connector 3.5 x 1.3)
35
.62
Discount for bigger quantity.
Interface specification: 8 x OUTPUTS (max 600mA), 8 x Digital INPUTS, 4 x Anlogue INPUTS, 2 x SERVO connector (5V), supply connectors (OUT) - 1 x 5V i 1 x 3,3V, 1 x UART connector (TX,RX), 1 x i2C connector, power supply connector for Raspberry and Interface ( 5.2 x 2.1 mm ), 1 x connector for 9V battery ( min. 1800 mA
). Interface dimension 73 x 62 mm. The interface is compatible with all Raspberry models that have a compatible connector with version 3. The adapter requires a min. 2500 mA 9V. VOLTAGE on INPUTS MAX. 9V. Separate connector (5V) to power the SERVO motor. SERVO motors can also be used with the Raspberry Pi 4 interface.
